thingiverse
Acetone bath
Механизм для обдува ABS в ацетоновой бане. Кроме печатных деталей потребуются винты м3 ...
acetone bath 3D Models
537 resultsSponsored
thingiverse
cults3d
Acetone bath
Механизм для обдува ABS в ацетоновой бане. Кроме печатных деталей потребуются винты м3 ...
thingiverse
Acetone Vapor Bath Container
Just wanted to share my Acetone Vapor Bath setup. The glass container has a 4.25" mou...
thingiverse
Acetone Bath With Magnets
Links to materials: M3x8mm screws Magnets 10x5mm for ...
thingiverse
Acetone Vapor Bath fan
https://www.thingiverse.com/thing:3027661
grabcad
Fan for acetone vapor bath
fan for acetone vapor bath. Based on one of the motors CD-ROM. Battery - 18650.
SPONSORED
⚽ Toy Soccer Cup — flick football, free
Free browser game · Real multiplayer · No install
thingiverse
Stackable acetone vapor bath rack
Print this in PLA and use it with AirWolf's paint can method (https://www.youtube.com/w...
cults3d
Stackable acetone vapor bath rack
Remix from thirdhorizon vapor bath rack : One piece rack for bigger printers Created ...
thingiverse
Storm in teacup (acetone bath)
Materials: - 4L sealed box made from PP - HDD motor from old 3.5" 250GB WD drive - M...
thingiverse
Paint Can Acetone Bath Tray
I use a paint can for smoothing out abs parts. I line the paint can with paper towel an...
thingiverse
Stackable acetone vapor bath rack
Remix from thirdhorizon vapor bath rack : One piece rack for bigger printers Created a ...
thingiverse
Acetone vapour bath for ABS prints
In order to rework an ABS print acetone can be used to make it more shiny and durable. ...
thingiverse
Acetone Vapor Bath Shelf - 25 cm
25 cm OD shelf for acetone vapor bath for use in 5 gallon bucket. Disclaimer: Do ...
pinshape
Air mixer (for cold acetone vapor bath)
Summary If you don't using some air mixer with acetone vapor bath, you must begin! Time...
thingiverse
Stackable acetone vapor bath rack magnetic top
Decided to make a magnetic top for this so that I could easily attach it / remove it fr...
thingiverse
Air mixer (for cold acetone vapor bath)
If you don't using some air mixer with acetone vapor bath, you must begin! Time for smo...
thingiverse
Acetone Vapor Bath Fan (for 5 gallon bucket)
Disclaimer: Do not perform an acetone vapor bath to smooth ABS parts. Performing aceton...
thingiverse
Air mixer (for cold acetone vapor bath) remix
NickRimmer's air mixer remix. I've extended hex neck to fit my box (20mm now). I've als...
thingiverse
Ø22mm Straight Coupling - ABS only, Acetone Vapour Bathe recommended.
Ø22mm Straight Coupling - ABS only, Acetone Vapour Bathe recommended. UPDATE PENDING ...
thingiverse
End Cap for 22mm Pipe Solvent Weld (ABS / Acetone Vapour Bath only)
End Cap for 22mm Pipe Solvent Weld (ABS / Acetone Vapour Bath only) Print with Good I...
thingiverse
Pipe Extender (ø22mm Solvent Weld) - Print in ABS and Acetone Vapour Bathe. (UNTESTED -PERMANENT)
Pipe Extender (ø22mm Solvent Weld) - Print in ABS and Acetone Vapour Bathe. UPDATE PE...
thingiverse
Speedloader 9 MM HP FN Browning
Facilita la carga de los cartuchos / Easy to load cartridges ...
thingiverse
Penis plug dilator
Print two from ABS so you will have two halves and glue it with abs-aceton sludge. Then...
thingiverse
Sea mine for drain stopper
Acetone bath is recommended
thingiverse
Heart Pendant with inset
ABS. The result after acetone bath.
thingiverse
Chrysalis with support
Added support for printing with Meshmixer. Printed at 0.35 with acetone bath
thingiverse
Tamiya Bruiser bumper
Rear bumper for Bruiser. I did smooth with acetone vapor bath and painted.
cults3d
Batman guitar capo
guitar capo, printed with abs and acetone bath. can also be printed with pla
cults3d
Penis plug dilator
Print ABS Then give it an acetone cold vapor bath to smooth the surface.
thingiverse
Penis plug dilator
Print ABS Then give it an acetone cold vapor bath to smooth the surface.
Sponsored